4K60 In-line Signal Re-Clocker with EDID Management
SKU: CON-H2-EDIDA multi-purpose installer tool, the CON-H2-EDID can perform a variety of tasks within an install. As an in-line device, it can act as an EDID manager to request specific content from a source, or as an audio de-embedder, extracting HDMI source audio via the S/PDIF or stereo mini-jack ports. Additionally, it can be a micro zone controller, sending CEC and RS-232 power triggers to connected projectors or screens and from its two relay ports, and can trigger devices in the zone using signal presence logic.

IN-LINE EDID EMULATOR
In a legacy installation scenario where EDID is not being communicated properly, the CON-H2-EDID can be connected in-line after the source device and using either a built-in or uploaded EDID file, can ensure the correct content is requested from the source.

IN-LINE EDID EMULATOR
In a legacy installation scenario where EDID is not being communicated properly, the CON-H2-EDID can be connected in-line after the source device and using either a built-in or uploaded EDID file, can ensure the correct content is requested from the source.
MICRO ZONE CONTROLLER
Working on signal presence logic, the CON-H2-EDID can trigger a connected screen or projector on/off via both CEC or RS-232; the RS-232 commands can be entered via the configuration s/w tool that is part of WMS. Additionally, at the same time, it can trigger 3rd party motors (projector screens, lifts, blinds & curtains) via the built-in relays.


4K SCALING IN ANY DIRECTION
Whether the requirement is to scale to or from the full capacity of HDMI2.0, the CON-H2-SCL allows incoming content to be converted (stripping HDR metadata if necessary) to a format compatible with the connected display or projector.

AUDIO DE-EMBED
Compatible with any current content thanks to its 18Gbps and HDCP2.2 support, it can be placed in-line after any source device and extract the incoming audio via the 3.5mm jack or coaxial S/PDIF port.

AUDIO DE-EMBED
Connected source devices or switchers that are sending 2ch PCM can have the audio de-embedded from the CON-H2-SCL via the Toslink port for connection to an external audio system.
HDMI2.0 MAXED OUT
Sporting an 18Gbps HDMI input, the CON-H2-EDID can support all UHD video signals up to and including 2160p 4:4:4/60, and high frame-rate HDR 12bit 4:2:2 up to 60Hz.


HDMI2.0 MAXED OUT
Sporting an 18Gbps HDMI input, the CON-H2-SCL can support all UHD video signals up to and including 2160p 4:4:4/60, and high frame-rate HDR 12bit 4:2:2 up to 60Hz.
Technical Specifications
Additional Features
AUDIO & VIDEO
Inputs
1x HDMI In: 19-pin HDMI Type A
Outputs
1x HDMI Out: 19-pin type A
1x Audio Out: 3.5mm (1/8in) TRS Stereo
1x S/PDIF Out: S/PDIF Coaxial Digital
Audio Formats
HDMI Pass-through: 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos
S/PDIF Out: De-Embed: 2ch PCM | Multichannel: Up to 5.1 DTS and Dolby Digital
Analog Out: 2ch
Video Resolution (Max)
1920x1080p @60Hz 12bit
3840x2160p @60Hz 12bit 4:2:2 HDR
4096x2160p @60Hz 8bit 4:4:4
Supported Standards
DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 | BT.2100
Maximum Pixel Clock
600MHz
COMMUNICATION & CONTROL
HDMI
HDMI 2.0 | HDCP 2.2 | EDID | CEC Triggering
Inputs supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included)
CEC
CEC Power Triggering | Requires CEC compatibility
RS-232
1x RS-232: 3-pin Terminal Block – 3.5mm
Relays
1x Relay 2: 3-pin Terminal Block – 3.5mm | 1x Relay 1: 3-pin Terminal Block – 3.5mm | Max 1A load
POWER
Power Supply
12V DC 0.5A
Max Power Consumption
≤2W
- In-line EDID manager with assignable presets or copy & import capability
- Assignable relays triggered on signal presence or via RS-232
- Source sensing power triggering:
-
- CEC: Compatible screens or projectors triggered manually via API or automatically on signal presence
- Serial: Power on/off commands can be stored and sent via RS-232 port
- Setup & configuration via simple PC configuration tool (WyreStorm Management Suite v1.6 or higher)
- Relay momentary or latching control
- Powered by 12v DC power supply (US, UK, EU and AU PSU pins included)
- Mounting brackets included
- USB-3-pin phoenix cable required for setup (not included) – Use P/n CAB-USB-PX1
Technical Specifications
AUDIO & VIDEO
Inputs
1x HDMI In: 19-pin HDMI Type A
Outputs
1x HDMI Out: 19-pin type A
1x Audio Out: 3.5mm (1/8in) TRS Stereo
1x S/PDIF Out: S/PDIF Coaxial Digital
Audio Formats
HDMI Pass-through: 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos
S/PDIF Out: De-Embed: 2ch PCM | Multichannel: Up to 5.1 DTS and Dolby Digital
Analog Out: 2ch
Video Resolution (Max)
1920x1080p @60Hz 12bit
3840x2160p @60Hz 12bit 4:2:2 HDR
4096x2160p @60Hz 8bit 4:4:4
Supported Standards
DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 | BT.2100
Maximum Pixel Clock
600MHz
COMMUNICATION & CONTROL
HDMI
HDMI 2.0 | HDCP 2.2 | EDID | CEC Triggering
Inputs supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included)
CEC
CEC Power Triggering | Requires CEC compatibility
RS-232
1x RS-232: 3-pin Terminal Block – 3.5mm
Relays
1x Relay 2: 3-pin Terminal Block – 3.5mm | 1x Relay 1: 3-pin Terminal Block – 3.5mm | Max 1A load
POWER
Power Supply
12V DC 0.5A
Max Power Consumption
≤2W
Additional Features
- In-line EDID manager with assignable presets or copy & import capability
- Assignable relays triggered on signal presence or via RS-232
- Source sensing power triggering:
-
- CEC: Compatible screens or projectors triggered manually via API or automatically on signal presence
- Serial: Power on/off commands can be stored and sent via RS-232 port
- Setup & configuration via simple PC configuration tool (WyreStorm Management Suite v1.6 or higher)
- Relay momentary or latching control
- Powered by 12v DC power supply (US, UK, EU and AU PSU pins included)
- Mounting brackets included
- USB-3-pin phoenix cable required for setup (not included) – Use P/n CAB-USB-PX1
In the Box
- 1x CON-H2-SCL
- 1x DC 12V 2A Power Supply (US/UK/EU/AU)
- 3x 3-Pin Terminal Block
- 2x Mounting Brackets
- 1x Quickstart Guide