3-Input In-wall HDBaseT Transmitter (2-gang UK)
SKU: SW-130-TX-UK3 inputs and powerful HDBaseT transmission result is this powerful switching transmitter, perfect for corporate meeting and classroom environments. Automatic or manual switching of 2 HDMI’s or USB-C and CEC power triggering via HDBaseT mean a simple user experience when it matters most. Further functionality allows USB devices to be routed back to the source via USB host (or natively via USB-C) and charging for the connected USB-C device.

3-INPUT SWITCHING TRANSMITTER
Setting a new standard for in-wall HDBaseT transmission, the SW-130-TX-US brings features of the WyreStorm range of professional switchers and packs them into a 2-gang form factor. Automatic or manual switching of the 3 connected sources (2 HDMI and USB-C) is possible with the USB-C supporting alt-mode functionality allowing a portable device such as a tablet or phone to be connected and send its content at up to 4K/30. HDCP 2.2 is also supported for the transmission of encrypted content.

3-INPUT SWITCHING TRANSMITTER
Setting a new standard for in-wall HDBaseT transmission, the SW-130-TX-US brings features of the WyreStorm range of professional switchers and packs them into a 2-gang form factor. Automatic or manual switching of the 3 connected sources (2 HDMI and USB-C) is possible with the USB-C supporting alt-mode functionality allowing a portable device such as a tablet or phone to be connected and send its content at up to 4K/30. HDCP 2.2 is also supported for the transmission of encrypted content.
FEATURES TURNED UP TO 11
It’s not all about the A/V when it comes to HDBaseT; with increased functionality on all fronts, the SW-130-TX can be used to send power triggers to a compatible connected screen, allowing centralized control and is PoH compatible meaning it can be passively powered over HDBaseT from a compatible receiver. The SW-130-TX can even power & charge a phone or tablet connected to the USB-C port so you don’t run out of juice mid-flow (max. 5v 2A)


FEATURES TURNED UP TO 11
It’s not all about the A/V when it comes to HDBaseT; with increased functionality on all fronts, the SW-130-TX can be used to send power triggers to a compatible connected screen, allowing centralized control and is PoH compatible meaning it can be passively powered over HDBaseT from a compatible receiver. The SW-130-TX can even power & charge a phone or tablet connected to the USB-C port so you don’t run out of juice mid-flow (max. 5v 2A)

HDCP 2.2 COMPATIBLE
The industry’s latest encryption standard designed to stop the illegal copying & distribution of 4K UHD content; no longer unique to residential solutions WyreStorm presentation switchers are fully compliant with HDCP 2.2, enabling you to de-centralize source devices within an installation.

HDCP 2.2 COMPATIBLE
The industry’s latest encryption standard designed to stop the illegal copying & distribution of 4K UHD content; no longer unique to residential solutions WyreStorm presentation switchers are fully compliant with HDCP 2.2, enabling you to de-centralize source devices within an installation.
USB 2.0 PASS-THROUGH
HDBaseT2.0 affords the addition of USB 2.0 pass-through, offering not only KVM functionality for extension of a keyboard/mouse or touchscreen but also full data transfer capabilities. The SW-130-TX has a USB host port allowing USB device data to be routed into the selected laptop (via HDMI). Going further, it can send USB device data natively through the USB-C port allowing a single cable to be used for A/V and USB device connectivity.


USB 2.0 PASS-THROUGH
HDBaseT2.0 affords the addition of USB 2.0 pass-through, offering not only KVM functionality for extension of a keyboard/mouse or touchscreen but also full data transfer capabilities. The SW-130-TX has a USB host port allowing USB device data to be routed into the selected laptop (via HDMI). Going further, it can send USB device data natively through the USB-C port allowing a single cable to be used for A/V and USB device connectivity.
Technical Specifications
TRANSMISSION
Transmission Encoding
HDBaseT Class C | PAM16 Encoding
End to End Latency
10µs
Max. Transmission Bit Rate
10.2Gbps
VIDEO
HDMI
(v2.0b) TMDS | 340MHz Maximum
Inputs
2x HDMI In: 19-pin type A1x USB-C In: USB 3.1c Audio/Video (4.5Gbps)
Outputs
1x HDBT out: 8-pin RJ45
Max Pixel Clock
HDMI & HDBaseT: 340MHz
Video Resolution (Max)
1920x1080p @60Hz
2560x1440p @60Hz
3840x2160p @30Hz 8bit 4:4:4
3840x2160p @30Hz 10bit 4:2:0 HDR
3840x2160p @30Hz 12bit 4:2:2 HDR
Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
Supported Standards
DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
AUDIO
Inputs
1x Audio In: 3.5mm (1/8in) TRS Stereo
2ch audio over HDBaseT | 1-way to RX
Audio Formats
2ch PCM | Multichannel up to DTS-X and Dolby Atmos
Maximum Sampling Rate
192KHz
Maximum Audio Channels
32
Audio Return Channel (ARC)
Not Supported
COMMUNICATION & CONTROL
USB Host (HDMI Inputs)
1x Type B host | Maximum data throughput: 190Mbps
HDMI
Alt-mode Supported | A/V and USB data from RX
USB 3.1c
HDMI | HDCP 2.2 | EDID | CEC | 2ch audio | USB
RS-232
1x RS-232: 4-pin Phoenix | Shared with 12v DC input
Compatible with WyreStorm TS-280 touchscreen via 4-pin phoenix port (only when using PoH)
HDCP
Pass-Through, 2.3 Supported
EDID
Pass-Through, from RX
Consumer Electronics Control (CEC)
One-way display trigger to RX
Auto Low Latency Mode (ALLM)
Supported
Variable Refresh Rate (VRR)
Supported
POWER
Power Supply
12V DC 1A (not included)
Max Power Consumption
7.8W
Power-over-HDBaseT (PoH)
Supported, 1-way from RX
Local Power Supply Input
4-pin Phoenix
Additional Features
- HDBaseT switcher/transmitter for video conference or meeting rooms
- Compatible with DVI-I and DP++ v1.3 signals from supported devices
- Additional 2ch analogue audio input for sending separate stereo audio to RX
- Automatic or manual CEC triggering for compatible connected screens or projectors
- Primary power supply via PoH from a supported receiving device (RX-700)
- Additional power input via DC port on rear via 12v 1A PSU (not included). Port shared with RS-232 input
- Control options include automatic switching, manual switching & CEC trigger and RS-232 control
- Compatible with TS-280 touchscreen for control with 12v power outlet
Technical Specifications
TRANSMISSION
Transmission Encoding
HDBaseT Class C | PAM16 Encoding
End to End Latency
10µs
Max. Transmission Bit Rate
10.2Gbps
VIDEO
HDMI
(v2.0b) TMDS | 340MHz Maximum
Inputs
2x HDMI In: 19-pin type A1x USB-C In: USB 3.1c Audio/Video (4.5Gbps)
Outputs
1x HDBT out: 8-pin RJ45
Max Pixel Clock
HDMI & HDBaseT: 340MHz
Video Resolution (Max)
1920x1080p @60Hz
2560x1440p @60Hz
3840x2160p @30Hz 8bit 4:4:4
3840x2160p @30Hz 10bit 4:2:0 HDR
3840x2160p @30Hz 12bit 4:2:2 HDR
Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
Supported Standards
DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
AUDIO
Inputs
1x Audio In: 3.5mm (1/8in) TRS Stereo
2ch audio over HDBaseT | 1-way to RX
Audio Formats
2ch PCM | Multichannel up to DTS-X and Dolby Atmos
Maximum Sampling Rate
192KHz
Maximum Audio Channels
32
Audio Return Channel (ARC)
Not Supported
COMMUNICATION & CONTROL
USB Host (HDMI Inputs)
1x Type B host | Maximum data throughput: 190Mbps
HDMI
Alt-mode Supported | A/V and USB data from RX
USB 3.1c
HDMI | HDCP 2.2 | EDID | CEC | 2ch audio | USB
RS-232
1x RS-232: 4-pin Phoenix | Shared with 12v DC input
Compatible with WyreStorm TS-280 touchscreen via 4-pin phoenix port (only when using PoH)
HDCP
Pass-Through, 2.3 Supported
EDID
Pass-Through, from RX
Consumer Electronics Control (CEC)
One-way display trigger to RX
Auto Low Latency Mode (ALLM)
Supported
Variable Refresh Rate (VRR)
Supported
POWER
Power Supply
12V DC 1A (not included)
Max Power Consumption
7.8W
Power-over-HDBaseT (PoH)
Supported, 1-way from RX
Local Power Supply Input
4-pin Phoenix
Additional Features
- HDBaseT switcher/transmitter for video conference or meeting rooms
- Compatible with DVI-I and DP++ v1.3 signals from supported devices
- Additional 2ch analogue audio input for sending separate stereo audio to RX
- Automatic or manual CEC triggering for compatible connected screens or projectors
- Primary power supply via PoH from a supported receiving device (RX-700)
- Additional power input via DC port on rear via 12v 1A PSU (not included). Port shared with RS-232 input
- Control options include automatic switching, manual switching & CEC trigger and RS-232 control
- Compatible with TS-280 touchscreen for control with 12v power outlet
In the Box
- 1x SW-130-TX-UK In-wall Transmitter
- 1x 4‐pin Phoenix Male Connector
- 1x USB host cable (Type A-B)
- 1x Decora face plate (SW-130-TX-UK)
- 4x Retaining screws (SW-130-TX-UK)
- 1x Quickstart guide